- #LINKSYS ROUTER EA6350 HOW TO#
- #LINKSYS ROUTER EA6350 SERIAL#
- #LINKSYS ROUTER EA6350 UPDATE#
- #LINKSYS ROUTER EA6350 DRIVER#
Under Category -> Session set Connection Type to Serial.Ĭlick Open. Under Category->Connection select Serial. Open the Network and Connection Settings and set your NIC IPv4 to static. Step 6: (set a static IP on the computer)Īttach the ethernet cable from the router to the computer.
#LINKSYS ROUTER EA6350 DRIVER#
I will not go deep on this but is very probably that you must download the correct driver for your adapter, in my case I had to download to a previous version to make it work. Step 5: Connect the USB adapter to the PC and open the device manager and look which COM number was assigned, we will use this information on a next step. *the color nomenclature is just as an example GND (black cable) - (black cable) GND (most right pin)
#LINKSYS ROUTER EA6350 HOW TO#
The cables for TXD and RXD must be crossed, but, How will you know how to connect them right in the board if they don’t have an identifier? Easy, just invert the cable that you connected next to the GND in the adapter like this: The GND pin is in the opposite side (most right pin), connect there the other end of the cable that you connect to the GND pin in the adapter. We will not use that pin but it will help us to identify the rest of the pins. Identify the 3.3V pin by looking for a little white arrow in front of the most left pin.
#LINKSYS ROUTER EA6350 SERIAL#
Step 4: Identify in the router's board the serial port at the left of the processor’s heat diffuser. Step 3: Connect the 3 Dupont cables to the TXD, RXD and GND pins of the USB to TTL adapter Step 2: Unplug the router and open it to get access to the board (you will plug it again until step 9) Give it an estimate of 5 minutes until you see the light stop flashing. Step 1: Unplug all Ethernet cables and do a factory Reset pressing the Reset button until you see flashing the light and wait until the startup process finish. Optional download Linksys firmware if you want to revert the dd-wrt flash.ĝownload last version of the firmware “linksys-ea6350-webflash.bin”.ĝownload tftpd32 or tftpd64 depending on your windows OS.ē female-female dupont cables to connect GND, TXD and RXD pins.For preference buy one that has labeled the type of pin (3.3V, TXD, RXD, GND, 5.5V) USB to 3.3V/5V TTL adapter (search for it at ebay or amazon).I had flashed with success my EA6350V2, through the serial port following this steps: Posted: Fri 11:14 Post subject: Flashing EA6350V2" Just somehow why after I reboot my router sometimes it back to stock firmware ? thanks
will give any result if there is a problem or not. The firmware in the link THEBOZ posted in this thread.Ĭan I use it for it said same for = EA6350 I try a lot firmware but back to stock after reset. I have a v2, but I can't get the linksys firmware to flash the webflash file. If you're not like me and don't lose the password to the web interface, it seems like ddwrt is working great I learned the lesson the hard way as I am locked out of the web interface with no other way to access the router. If you do decide to flash ddwrt, do know that the reset button only resets the stock partition's data not ddwrt's, hence the reset does not work for DDWRT. If you do want to go back to the stock firmware, do a 30/30/30 reset. It does not reboot to the second partition with the stock firmware.
#LINKSYS ROUTER EA6350 UPDATE#
To anyone with the ea6350v2, it seems like if you update to the latest official firmware and then flash latest ddwrt it works. Theboz been going over 45 days now so he said When you say for a while do you have a time limit. It seems to work fine for a while but eventually will reboot to the original firmware. Normal firmware upgrade from linksys interface I am far from a guru, I'm barely a novice. Flash it twice with the same dd-wrt build, that way when it boots into the other partition, it will still be in dd-wrt.
0 kommentar(er)
